2013年8月30日星期五

Findint the balsa wood airplanes

Finished balsa wood weights can vary for a variety of reasons. These include the age and size of the tree, location of the trunk cut and the kiln drying process. Commercial balsa wood used formodel airplane construction typically weighs between 6 and 18 pounds per cubic foot. The most commonweights available are between 8 to 12 pounds per cubic foot. Six pounds or less is considered contest grade wood.
The strength of balsa varies in direct relation to its density or weight - the heavier the wood the stronger it is. The above chart was designed with 10 lb./cu. ft. balsa as the median. In other words, balsa at IO Ibs./cu. ft. has been tested given a value of 100. The other woods were then tested in the same way and given a figure that is numerically in proportion. By comparing the relative strength figures in the chart, it will be seen that balsa is as strong or stronger, pound for pound, than most of the species shown.
Finished balsa wood, like you find in model airplane kits, varies widely in weight. Balsa is occasionally found weighing as little as 4 lbs. per cu. ft. On the other hand, you can also find balsa which will weigh 24 lbs or more per cu. ft. However, the general run of commercial balsa for model airplanes will weigh between 6 and 18 pounds per cu. ft. Eight to twelve pound balsa is considered medium or average weight, and is the most plentiful. Six pound or less is considered "contest grade", which is very rare and sometimes even impossible to obtain.
Because the range of balsa wood densities can vary so much, a modeler must specify the types of balsa wood desired. Use the lightest grades possible for sections of your model that do not bear weight or require strength, such as nose cowls, fill-in and shaped wing tips. Select a heavier cut of wood for areas requiring strength such as wing spars, fuselage formers and stringers.
Article resource: http://www.balsafactory.com/

2013年8月29日星期四

Pine comes in several varieties

Pine
Pine comes in several varieties, including Ponderosa, Sugar, White, and Yellow, and all of them make great furniture. In some areas of the country (especially southwest United States), pine is the wood to use. Pine is very easy to work with and, because most varieties are relatively soft, it lends itself to carving.Here to know more about balsa wood, which is the softest wood in the world.
Pine generally takes stain very well (as long as you seal the wood first), although Ponderosa pine tends to ooze sap, so be careful when using this stuff. Pine is available from most home centers, but it's often of a lesser grade than what you can find at a decent lumberyard.
Redwood
Like cedar, redwood is used mostly for outdoor projects because of its resistance to moisture. Redwood (California redwood) is fairly soft and has a straight grain. As its name suggests, it has a reddish tint to it. Redwood is easy to work with, is relatively soft (2 on a scale of 1 to 4), and is moderately priced. You can find redwood at your local home center.
Homing in on hardwoods
Most woodworkers love to work with hardwoods. The variety of colors, textures, and grain patterns makes for some beautiful and interesting-looking furniture. The downside to hardwoods is their price. Some of the more exotic species can be too expensive to use for anything more than an accent.
Some hardwoods are becoming very hard to find and are being harvested without concern to their eventual extinction (Brazilian rosewood comes to mind). Not only is this hard on the environment, it drives the price of the wood so high that making furniture out of it is out of the question for most woodworkers. If you can, try to buy wood from a sustainable forest (commercial tree farms that ensure the supply of the wood). Check out the National Hardwood Lumber Association for ways to support sustainable forestry.
Following is a list of common hardwoods and their characteristics.
For more, are you also interested in balsa block , you can take a more information in our website http://www.balsafactory.com/ .

2013年8月27日星期二

Tips on consturct balsa RC model

Once balsa RC model is constructed, you should paint it actually. Balsa wood is well known among consumers for lightweight, soft and easy to work with. As we have introduced in our previous articles, balsa wood is light since it has special construction cells. The cells are large within thin walls. Although there are other woods that are lighter than balsa, they are not ideal choices for making RC model since they are weaker and can't bear high stress. Paint the balsa RC model is simple, you can follow me to know more detailed information.
First of all, prepare something that you will use during your painting process, like drop cloths, 80-grit sandpaper, clean cloth, sealant, paint brushes, white primer, paint, painter's tape and so forth. Generally, you are advised to paint your model in a well-lighted area. What should you know is that you should paint all sides of the RC model and you should see the plane model from every angle to ensure all fzbmcihlwd angle has been painted. You should add a layer of clear coat paint after the paint has dried if you want your RC model to have a glossy appearance. When you choose paint, you should take consideration of your model power type. Acrylic paint is more susceptible to attack by liquids like alcohol if your model is powered by a fuel rather than battery.
lay out drop cloths beneath your completed RC model. The drop cloths may vary in size, depending on the size of your model.
use a sandpaper to sand the balsa wood surface. Wipe away the excess wood dust by swiping a clean cloth across the surface of the balsa wood.
use a paint brush to apply a coat of sealant to the wood. Small paint brushes used for artistic paintings work well actually. And various sizes may be available to suit your model size. Use the clean paint brush to prime the RC model. Add a coat of white primer and the primer will help make the paint adhere well to the plane and not peel off.
paint your model with your favorite color. Wait until one color dries before applying the next color. Use painter's tape to obtain straight lines as long as you like.
Here to know more about balsa round , And this article comes from website http://www.balsafactory.com/ .

2013年8月23日星期五

What is the difference between a hardwood and a softwood?

As it turns out, a hardwood is not necessarily a harder material (more dense) and a softwood is not necessarily a softer material (less dense). For example, balsa wood is one of the lightest, least dense woods there is, and it's considered a hardwood.If you are also intereted in balsa wood, you can go to our website.
The distinction between hardwood and softwood actually has to do with plant reproduction. All trees reproduce by producing seeds, but the seed structure varies. Hardwood trees are angiosperms, plants that produce seeds with some sort of covering. This might be a fruit, such as an apple, or a hard shell, such as an acorn.
Softwoods, on the other hand, are gymnosperms. These plants let seeds fall to the ground as is, with no covering. Pine trees, which grow seeds in hard cones, fall into this category. In conifers like pines, these seeds are released into the wind once they mature. This spreads the plant's seed over a wider area.
For the most part, angiosperm trees lose their leaves during cold czmcihlwd weather while gymnosperm trees keep their leaves all year round. So, it's also accurate to say evergreens are softwoods and deciduous trees are hardwoods.
The hardwood/softwood terminology does make some sense. Evergreens do tend to be less dense than deciduous trees, and therefore easier to cut, while most hardwoods tend to be more dense, and therefore sturdier. But, as the classification of balsa wood demonstrates, there is no minimum weight requirement to become a hardwood.
Know more about balsa rectangle in our website , and you can use these softwood to make models, such as airplane, glider,or even bridge. This article comes from http://www.balsafactory.com/ .

2013年8月22日星期四

Properties of those softwoods

PINE: Pine is a softwood which grows in most areas of the Northern Hemisphere. There are more than 100 species worldwideYou may also want to know the info about the softwood balsa . Here to know more. .
Properties: Pine is a soft, white or pale yellow wood which is light weight, straight grained and lacks figure. It resists shrinking and swelling. Knotty pine is often used for decorative effect.
Uses: Pine is often used for country or provincial furniture. xzmcdhlwd  Pickled, whitened, painted and oil finishes are often used on this wood.
ASH: There are 16 species of ash which grow in the eastern United States. Of these, the white ash is the largest and most commercially important.
Properties: Ash is a hard, heavy, ring porous hardwood. It has a prominent grain that resembles oak, and a white to light brown color. Ash can be differentiated from hickory (pecan) which it also resembles, by white dots in the darker summerwood which can be seen with the naked eye. Ash burls have a twisted, interwoven figure.
Uses: Ash is widely used for structural frames and steam bent furniture pieces. It is often less expensive than comparable hardwoods.
HICKORY: There are 15 species of hickory in the eastern United States, eight of which are commercially important.
Properties: Hickory is one of the heaviest and hardest woods available. Pecan is a species of hickory sometimes used in furniture. It has a close grain without much figure.
Uses: Wood from the hickory is used for structural parts, especially where strength and thinness are required. Decorative hickory veneers are also commonly used.
BEECH: The American beech is a single species which grows in the eastern half of the United States.
Properties & Uses: Beech is a hard, strong, heavy wood with tiny pores and large conspicuous medullary rays, similar in appearance to maple. This relatively inexpensive wood has reddish brown heartwood and light sapwood. Beech is often used for frames, a variety of bent and turned parts. Quarter sliced and half round cut beech veneers are commonly used.
Here to know more about balsa round, article resource: http://www.balsafactory.com/ .

2013年8月21日星期三

Why to use balsa wood make models ?

For the hobby makers across the globe, there are few types of woods they prefer to xzmbchlwd choose to make models. Among them, balsa wood is always the most favourite type. The balsa wood is flexible and strong, and so it could ease the difficulty to assemble the models and guarantee the strength at the same time. If fact, the flexibility and stability expand the application of balsa wood. In other fields, including building the real planes and boats, balsa wood could make its effort.
Balsa tree comes from the South America. The aborigines used it to make the boats and the boats have been prevened to be strong and flexible. Perhaps the hobby makers have other choices while making other models. For example, the bicycle models or the tower models could be made from the steel wires. Frankly, while making these models, the wires are more suitable than the balsa wood. However, when it comes to make boat models, the balsa wood is the choice that could not be better.
The steel may sink while placing on the water. Even you are endowed with the gift to create a pressure-tight air chamber to stop sinking, you would have to make more effort to prevent the rust. If the hobby makers choose the balsa wood to make the boat models, as we all know, the density of the wood is lighter than the water, so the wood could float on the surface of the water for its original nature. Besides, the makers never need to worry about the rust. All they need to do is to paint the boat to prevent the rotting.
While the hobby makers are going to make the model planes, they will choose the balsa wood as well. That is because of its lighter weight. Generally, the planes need to to lighter and so it could fly with less energy. If you choose the steel or other metal material to make the planes, you will have to make a greater effort to enhance the capacity of the power engine.
Further more, the balsa wood is easy to assemble. You could glue the pieces of balsa woods together with the suitable adhesives while there are none type of adhesives which are designed for the metals. So if you are going to make the models, balsa wood would be your best choice..IF you may also want to know more about balsa block , you can go to our website to find the knowledge about them. Here is the website: http://www.balsafactory.com/.

2013年8月20日星期二

why people prefer to make balsa surfboard nowadays?

Do you know why people prefer to make balsa surfboard nowadays? To tell you the truth, the balsa wood was the favourite material to make surfboard once. But with the presence of plastic material at the begin of last century, the fame of balsa wood was decreased. However, the fever of balsa surfboard has come back in the past decades due to the concept of environmental protection. While you see the surfers who are fighting with the waves, no matter in Hawaii or at the beach of California, the materials used to create surfboard are mainly balsa wood.
While people choose the plastic materials to make surfboard, they are attracted by the cheaper price and its resistance to water. Besides, some types of plastic are designed with the ability to absorb the shock and retain the original shape while suffering from huge pressure. But as we all know, the plastic is difficult to be disposed. For example, nowadays, the so called "white pollution" is caused by the abuse of plastic bags.
On the contrary, the balsa wood is much more environmental friendly. With the excellent skills, the workers could carve the balsa wood into the most proper shape to fight with the waves. The balsa wood is born with amazing buoyancy and so the surfers could perform better. The stable structure of the balsa wood could enhance the safety of the players. While the balsa surfboards are broker, they could be burned completely. As compared with its counterpart, the plastic surfboards would cause much trouble while they are not useful.
If you are planning to make surfboard by yourself, balsa wood would be your best choice. It is difficult to find the plastic board with the suitable shape while the balsa wood is easy to purchase online. In addition, the wood is easy to cut and you could be in full control of the production process. But you should be knowledgeable about the mechanics which means you should know how the board could endure more pressure, how the board could go through the wave better and how to make the board to meet your body.
Of course, the balsa wood attain wider applications except for being used to make surfboards. It is the most popular wood to make models and it has played an important role in the production of buoyant apparatus. If you are looking for the high quality balsa wood, no matter you are using it for which kind of purpose.For more, if you are also interested in bass polywood , you can go to our website to know more.
Article resource: http://www.balsafactory.com/.

2013年8月18日星期日

Propagate Your Shrubs from Softwood Cuttings



I have propagated thousands of new shrubs from softwood cuttings. That may sound like a lot, but since I'm a propagator at a nursery, it's all in a day's work. To successfully propagate such a large number of shrubs requires specially designed hoop houses g4nmkvkz and state-of-the-art misting and heating systems. It's also handy to have helpers to carefully monitor the health and well-being of each cutting.For more, if you want to know more about the softwood balsa, then you can take a look into our website. You know that the balsa wood can make your different kinds of model.
On a smaller scale, though, it is possible to propagate deciduous shrubs from cuttings taken during the summer without the all the high-tech machinery and costly gadgets I have at the nursery. By creating favorable conditions, using the right tools, which are actually quite simple, and being patient, you can achieve success with softwood cuttings at home, too.
Harvest cuttings from semi-ripe growth
The trickiest part of propagating shrubs from softwood cuttings is knowing when a shrub's stems are ready to be cut. Softwood, the section of a shrub's stem that's neither brand new nor fully mature, is the stage of growth on a deciduous woody plant that is best suited for rooting (for details, see Softwood is neither green nor woody, below). The newer, green growth that lies at the end of the stem will rot before roots are produced, and the older, more woody growth at the base of the stem has a harder time putting out roots.
Softwood cuttings can be taken from most deciduous shrubs in June and July and sometimes into early August. I determine a stem's maturity by taking it in my hand and bending it. If the stem breaks with a characteristic snapping sound, it is in the softwood stage and ready to be harvested as a cutting. If the stem is still too green, it will bend but not break. If the stem is entering the woody stage, it won't bend at all.Here to know more about balsa block , article resource: http://www.balsafactory.com/.

2013年8月14日星期三

Knowing the information about Oak wood

Oak, Pin
Pin oak is one of the most overused landscape oak in the midwest and eastern United States. The oak is popular due to an attractive pyramidal shape and straight, dominant trunk, even on older specimens and availability. A lot of that popularity has been challenged because of iron-deficiency chlorosis, persistent brown leaves on the tree into the winter, and a ragged look with the stubby twig "pins" that stand out and is a negative to some.For more if you interesed in the softwood balsa , you can take information in our webiste.
Oak, Post
The name post oak refers to the use of the wood of this tree for fence posts. Its wood, like that of the other white oaks, is hard, tough and rot-resistant. The "Maltese cross" form of the distinctive post oak leaf is a key identifier. Both the post oak and the blackjack oak form the "Cross Timbers" in Texas and Oklahoma. This area comprises the border where trees transition to prairie grassland.
Oak, Northern Red
Any oak with pointed, bristle-tipped leaf lobes belong to qyexbictzs the red oak group, including Northern red oak. Red oak is the fastest growing of all oaks and when on the right site, one of the largest and longest lived. Northern red oak and is an easily transplanted, popular shade tree with good form and dense foliage. Northern red oak is well adapted to periodic fires.
Oak, Nuttall
Nuttall oak (Quercus nuttallii), not distinguished as a species until 1927, is also called red oak, Red River oak, and pin oak. It is one of the few commercially important species found on poorly drained clay flats and low bottoms of the Gulf Coastal Plain and north in the Mississippi and Red River Valleys. The acorn or winter buds identify Nuttall oak, easily confused with pin oak (Q. palustris). The lumber is often cut and sold as red oak. In addition to producing timber, Nuttall oak is an important species for wildlife management because of heavy annual mast production. By the way , if you are looking for some wood to make models you can take a look at end grain balsa in our wesite.
Article resource: http://www.balsafactory.com/

2013年8月13日星期二

Knowing oka and maple three

Maple, Sugar
Sugar maple is a maple native to the hardwood forests of northeastern North America, from Nova Scotia west to southern Ontario, and south to Georgia and Texas. Sugar maple is an immensely important species to the ecology of many forests in North America. Sugar maples engage in hydraulic lift, drawing water from lower soil layers and exuding that water into upper, drier soil layers. This not only benefits the tree itself but also many other plants growing around it. Sugar Maple is the major source of sap for making maple syrup and prized for furniture and flooring.For more if you are interested in balsa  wood (balsa tree), you can visit our website.the quality balsa round is for you.
Oak, Black
Black oak has readily hybridized with other members of the red oak group of oaks being one parent in at least a dozen different named hybrids. This single species' compatibility is fairly uncommon in the [i]Quercus[/i] genus group. Black oak is seldom used for landscaping. The inner bark of the black oak contains a yellow pigment called quercitron, which was sold commercially in Europe until the 1940s.
Oak, Bur
The bur oak, (Quercus macrocarpa), sometimes spelled burr oak, is a species of oak in the white oak group. Bur Oak typically grows in the open, away from forest canopy. For this reason, it is an important tree on the eastern prairies, where it is often found near waterways in more forested areas, where there is a break in the canopy. It is an excellent landscaping tree.
 Oak, Cherrybark
Cherrybark oak (Q. pagodifolia) is fairly common large tree of bottomland forests, similar to the upland Southern red oak (Q. falcata), of which it was formerly considered a variety. The cherrybark tree has heavy strong wood that makes it an excellent timber tree for furniture and interior finish. It is a commercially desirable tree and managed for various forest products.
Article resource: http://www.balsafactory.com/ .

2013年8月8日星期四

New balsa wood exhibit

Balsa wood is an integral part of building model airplanes. To allow our visitors to learn more about this, we’re in the process of installing an exhibit in the hands-on gallery exploring the life cycle of balsa wood.
Here’s the how the exhibit progressed.
1. A stylized balsa tree graphic was created. During this process, various designs were projected onto the wall to get a sense of size and space.
2. The components of the trees were cut out of Sintra material, sanded and finished before being installed with the help of nails and Velcro.
3. A dome normally used for skylights was reinvented as an exhibit case. Care was taken to install pxbkctbsd it flush against the wall, but in a way that doesn’t make it obvious.
4. Shelving and mounts were created to hold various things inside the dome.
5. Intern Samantha Weaver researched how balsa trees grow and the various cuts and grains that are available from the wood.
6. She turned all of this research into fun facts for the exhibit and created labels.
7. Everything was installed. Inside the dome are pieces of balsa in different stages of processing and in different cuts for different purposes.
The future will bring a hands-on station where visitors will be able to experience building a wing by following a set of plans. Unfortunately, we don’t have the ability to use real balsa wood for this, so Sintra pieces are going to be used instead. The idea of how assembling a model works though, will come across.
Article resource: http://www.balsafactory.com/ .

Here comes the density of balsa

Here comes the density of balsa . The balsa wood varies widely in density. Believe it or not, the balsa ever being found weighing as little as 4 lbs. per cu. ft. However, there are also balsa weighing as much as 25 lbs. or more per cu. ft. Generally, the average weight of commercial balsa will weigh between 6 lbs. per cu. ft. The average weight of balsa should be 8 to 12 lb and the most plentiful. Six pounds or less is very rare and difficult to obtain.
When selecting balsa, you are advised to choose the most light one. You are advised to take consideration of the way the grain runs through the sheet as well as the weight of the sheet as we discussed above. The rigidity or flexibility of a balsa sheet mainly depend on the grain direction actually. Frankly speaking, SYNHONG is one of the most famous supplier of balsa.
Second, you should use a pencil to mark the cutting lines or trace the outline of the shapes to be cut out with a straightedge. Well, as we all know that balsa is very expensive, so it is important to measure and mark the cut lines before you really cut in case of the unsuccessful cutting.
Third, you are advised to place a clamp at two opposite ends of the sheet. Secure the wood sheet to the table with C-clamps or mini clamps. Well, place your straightedge along the cut line. The straightedge will help you a lot when you cut straightly. It can be regarded as a guide actually. Run your hobby knife blade along the side of straight edge applying light pressure to score the cutting line. Make a second run along the cutting line applying a bit more pressure.
As we have introduced before, balsa wood is the soft and lightweight wood type which is suitable in making models and so forth. It is also very strong and easy to work with. And it can be classified into 3 different grains according to the corresponding features and standards. Frankly, balsa is different in its thickness. It is of great importance to cut balsa wood with the proper tool and in a proper way. Everyone should try their best to cut it properly to avoid the waste since it is very expensive.
In order to cut the balsa wood in a proper way, you are advised to prepare the things as follows: balsa wood, cutting board, modeling knife, straightedge, clamps, pencil, 220-grit sandpaper and so on. Or, you can choose to cut it with the saw actually. Then you need to prepare saw if you tend to use it.
First of all, you should place balsa wood sheet on a worktable. You are advised to place a cutting board between the balsa wood and the table to protect the table surface and the tip of the hobby knife blade. Generally, this should be regarded as the basic step actually.
article resource: http://www.balsafactory.com/.

2013年8月7日星期三

a "perfect" sheet of C grain blasa wood

Balsa grading is done based on the orientation of the cells in the balsa . Balsa has two main types of cells, longitudinal and radial. As the tree is standing, the longitudinal cells are vertical, and the radial cells (or rays...) are horizontal, from the center of the tree out. In the picture below, the longitudinal cells appear as dots, and the rays appear as lines.
Grading balsa has been done in the same way for over 60 years. The standard designations of A, B, and C have been use to describe the grain orientation of the cut sheet, and a view of how the sheets are cut from the balsa billet are shown below. (Note that the rectangles with the grain designations would represent the -end- of a balsa sheet...)
A grain is that which has the longitudnial cells running the length of the sheet, and the rays perpendicular to the sheet. A grain is generally used for wing spars and outlines, and is more readily bent around forms for wing tips. Note in the picture below you can see the long darker cells, which are the longitudinal cells. This contributes to the stiffness over the length of the sheet, and why it is suited well for spars. A grain sheets, due to the orientation from the original log, generally have a high degree of uniformity from the sheet, since all of the width of the sheet came from the same growth cycle of the tree. A grain is also very flexible across the width of the sheet, and stiffest along the lenght of the sheet.
C grain has the rays oriented across the width of the sheet, and a "perfect" sheet of C grain should look like this:
Note that you can see the rays traveling virtually the entire width of the sheet, which contributes to the stiffness. C grain is generally used for ribs, motorsticks, and booms, and is very stiff when rolled into tubes. C grain is somewhat like a natural plywood, due to the orientation of the longitudinal and radial cells, and has charistics of plywood in that respect. As a billet of balsa is being cut for C grain, due to the nature of the growth rings, the billet will eventually not be "perfect" C grain. In the picture below, you can see a sheet cut which is typically considered C grain, but is a few degrees from a true C grain sheet.
As the sheets diverge from being cut along the rays, the sheet takes on a more mottled apperance instead of distinct wide lines, and eventually turns into B grain.
"Mottled" C grain and BC grain can many times be used as effectively as "perfect" C grain. In gdjlhqgnvz fact, some actually prefer BC grain for some applications, as when a tube made from it does break, it can be easier to repair. Grading of balsa is obviously not a science, and many sheets could fall into either category, but generally the predominate characteristic of the sheet will be used for the final grading.
In any given billet, you can theoretically orient the billet to get any of the above grains. However, some billets are more suited to one grade or the other, and generally sheets are cut in the orientation that is most efficient and has the highest yield. As you can see in the above picture, a billet oriented with A grain on the top would not need to be rotated during the cutting process much if at all, and all sheets would basically be "perfect" A grain. Balsa stock generally comes in 3"x3"x36" blocks, which then are cut in two, (for the standard 18" sheet length") and then each block is sawn in two, with each billet measuring approximately 1.25"x3"x18".
It is almost always possible to orient a 3"x3" block to get perfect grain orientation, but since low density balsa stock is in fairly short supply, and in the attempt to get the highest balance of yield to quality, some billets are cut "as is" instead of cutting them up to get a perfect billet. In other words, given a block of good 4# balsa, it is better to have two billets than one, i.e. twice as many sheets. This is where the in-between grades of AB, B, and BC generally come from.
During the cutting process, my setup allows me to angle the billet to optimize the grain orientation. However, on each change, the billet has to be squared off before the cut, resulting in waste and less yield. Depending on the particular billet being sawn, this may or may not be desireable. Due to the lower yield when cutting sheets graded as either AP or CP ("perfect" A or C grain) are priced at a slight premium.?
article resource: http://www.balsafactory.com/ .

2013年8月6日星期二

How to Bend Balsa Wood ?

Are you wondering how to bend the balsa wood. By this aricle you will learn more information about bend these balsa wood in the right way.  balsa wood is often the wood of choice when a woodworking project involves curves that require the wood to be bent. Special methods for bending balsa wood may not be necessary if the curve is a gentle one and the radius is large; the wood may conform axtmdjbfzx easily. For more complex or tighter curves, however, use some specific practices to ensure that the balsa wood will bend without breaking or splitting.
Select A-grain balsa wood for more difficult curves and bends. A-grain wood is more flexible than B or C-grain pieces, which are more likely to split when bent. When possible, bend the wood so that the grain of the wood runs with the longest side of the piece.
Submerge the balsa wood in a container filled with a mixture of equal parts warm water and ammonia. Allow it so soak for at least an hour—longer for thicker pieces. This solution breaks down the balsa at the cellular level and is thus especially effective in making the balsa wood more flexible.
Place the wood against the curved form or template and shape it to fit. Tape the wood down to hold it in place and allow it to dry thoroughly. Do not attempt to glue the wood while it is wet. Depending on temperatures and humidity, this may take two to three days or more.
Remove the tape from the wood when it is dry. The wood will spring back away from the form or template a little, but that is normal.
Spread the glue on the wood with the brush and press the wood back to fit the form or template. Secure it in place with tape again and remove the tape after the amount of drying time recommended by the glue manufacturer.If you want to know more information about balsa wood, go to our website here : http://www.balsafactory.com/.

2013年8月5日星期一

balsa is used in many common modeling application

Balsa wood is a lightweight wood used by many modelers for its high strength-to-weight ration and the ease with which it is worked. balsa is used in many common modeling applications from bridge and tower building for engineering contests to remote-controlled model aircraft bodies. While balsa is well suited for building frames for models the frames need to be covered in order to complete the look of the model. A widely used covering technique involves placing a skin on the models made of tissue paper. Using tissue paper retains the lightness of the model while creating a model cover that can be easily painted, completing the look of your model.
Instructions
Remove any rough spots on the surface of the model to be covered with the tissue paper using the sandpaper.
Lay a sheet of tissue paper onto a flat surface large enough to cover a side of the model. Place the model on the center of the paper and trace a line one-quarter inch around the model's edge. Remove the model and then cut along the line traced into the tissue. This tissue will serve as the covering skin for that portion of your model.
Use a paintbrush to brush the model with the adhesive where the tissue will be placed. Apply the adhesive lightly, as too much will soak the wood, causing warping. Brush all areas where the adhesive will be placed, not just that of the cut tissue. Wait 2 hours for the adhesive to dry on the balsa surface.
Spray the tissue with a light mist of water. The tissue should be slightly damp to the axtmdjbfzzc touch, but not wet. Place the damp tissue onto the model, with the extra tissue falling over the edges. Using the paintbrush, brush a light layer of adhesive over the tissue where it meets the wood surface beneath. Fold the overhanging tissue along the sides of the model and brush the overhanging tissue with the adhesive as well. Because the tissue is damp, the adhesive will combine with the water and bind to the already placed layer of adhesive dried onto the model. Wait another 2 hours for the tissue and adhesive to dry and then repeat the process to cover the remainder of the model. The drying tissue shrinks onto the model, creating a smooth surface suitable for painting.
Tips & Warnings
The clear dope adhesive emits fumes that can be dangerous when breathed for long lengths of time. The covering process should be completed only in a ventilated area.For more related article comes from http://www.balsafactory.com/.

2013年8月1日星期四

my experice of fly balsa wood planes

As a full fledged member of the aging (yet never old) baby boomers generation, I have vivid memories of balsa wood gliders from my youth. In a continual example of "hope springs eternal," we would buy a set at least once a year. Every year I've hoped for the same thing. That they would be easy to put together and fly perfectly.
Every year the results were the same. My klutzy fingers would manage to break some part of the plane and there went my flying dream, straight down the tubes!
Recently, when shopping for some fun activities and projects for my grandchildren and kxiugtka me to enjoy, I came across a set of these balsa wood gliders for $1 each. Cheap enough, even for grandparents on a budget. I popped five into my cart along with some other interesting plastic toy airplanes.
Later that day we pulled out the balsa wood gliders and tried to put them together. The grandchilden went first. When they saw the balsa wood start to crack, they quickly handed it all to me. "Help, grandma! They're breaking!" they cried out.
Not surprised, I took each plane gingerly and did my best to gently slide the wings through the slit. Since it has to be tight in order to hold the wing, I guess it's not surprising it's hard to do this correctly. Finally we successfully completed two out of the five I had bought. One of those two balsa wood gliders crashed and broke a little bit later.
Hmmm, seems some things never change! Then again, the other type of planes I bought were just as cheap but worked much better!
We all know that balsa wood is the best wood for our models. but where to get those quality balsa  with reasonable price. Here i highly recommend you a professional online store for the website is http://www.balsafactory.com/.

Balsa Wood is currently used in various

balsa wood is really a light-weight wood range obtained from trees and shrubs from the exact same title which are in the rainforests associated with Main The united states, South usa, and some additional areas. The actual comfortable as well as damp problems within these types of places tend to be well suited for the actual development of the grow. Balsa trees and shrubs develop very quickly âEUR" this typically takes under ten years for any sapling to become older sufficient with regard to reducing. Nevertheless, as soon as after dark ten-year gun, a good unharvested sapling might solidify on the exterior as well as decay within, making it the ineffective item.
At first, balsa wood had been just obtained from the actual jungles. However because of broad customer pursuits and also the success from the business, maqui berry farmers possess started their very own plantations. Ecuador is basically accountable for the planet way to obtain the actual wood, then providers through Indian, Philippines and also the Caribbean.
Typical Utilizes with regard to Balsa
Balsa wood was initially utilized throughout Globe Battle We as an alternative with regard muxtpvix to cork. In those times, existence rafts as well as armour dishes had been made of balsa. Within Globe Battle II, balsa make use of had been improved for that producing associated with planes. This grew to become the main materials for that well-known Uk de Havilland Mosquito fight plane.
Aside from becoming light-weight as well as long lasting, balsa wood additionally is able to drift, that makes it a perfect materials with regard to surfboards along with other drinking water sports activities gear. An additional well-liked make use of with regard to balsa wood is actually design packages, generally which associated with planes. Once again, since the materials is actually gentle, design planes made of balsa usually carry out much better than it's additional counterparts. Toy homes and also the small furnishings which go with all of them will also be regularly made from balsa. Exactly the same holds true with regard to phase furnishings along with other props. Another areas of the actual balsa sapling are utilized with regard to padding, padding, sound-absorption as well as packaging.More related article comes from http://www.balsafactory.com/.